Attachment RadHaz

This document pretains to SES-LIC-20141223-00922 for License on a Satellite Earth Station filing.

IBFS_SESLIC2014122300922_1069756

Exhibit Radiation Hazard Report Page 1 of 10 Analysis of Non-Ionizing Radiation for a 2.4-Meter C-band Earth Station System This report analyzes the non-ionizing radiation levels for a 2.4-meter earth station system. The analysis and calculations performed in this report comply with the methods described in the FCC Office of Engineering and Technology Bulletin, No. 65 first published in 1985 and revised in 1997 in Edition 97-01. The radiation safety limits used in the analysis are in conformance with the FCC R&O 96-326. Bulletin No. 65 and the FCC R&O specifies that there are two separate tiers of exposure limits that are dependant on the situation in which the exposure takes place and/or the status of the individuals who are subject to the exposure. The Maximum Permissible Exposure (MPE) limits for persons in a General Population/Uncontrolled environment are shown in Table 1. The General Population/Uncontrolled MPE is a function of transmit frequency and is for an exposure period of thirty minutes or less. The MPE limits for persons in an Occupational/Controlled environment are shown in Table 2. The Occupational MPE is a function of transmit frequency and is for an exposure period of six minutes or less. The purpose of the analysis described in this report is to determine the power flux density levels of the earth station in the far-field, near-field, transition region, between the subreflector or feed and main reflector surface, at the main reflector surface, and between the antenna edge and the ground and to compare these levels to the specified MPEs. Table 1. Limits for General Population/Uncontrolled Exposure (MPE) Frequency Range (MHz) Power Density (mW/cm2) 30-300 0.2 300-1500 Frequency (MHz)*(0.8/1200) 1500-100,000 1.0 Table 2. Limits for Occupational/Controlled Exposure (MPE) Frequency Range (MHz) Power Density (mW/cm2) 30-300 1.0 300-1500 Frequency (MHz)*(4.0/1200) 1500-100,000 5.0 Table 3. Formulas and Parameters Used for Determining Power Flux Densities Parameter Symbol Formula Value Units Antenna Diameter D Input 2.4 m Antenna Surface Area Asurface π D2 / 4 4.52 m2 Feed Flange Diameter Dfa Input 7.6 cm Area of Feed Flange Afa π Dfa 2/4 45.60 cm2 Frequency F Input 6175 MHz Wavelength λ 300 / F 0.048583 m Transmit Power P Input 400.00 W Antenna Gain (dBi) Ges Input 41.8 dBi Antenna Gain (factor) G 10Ges/10 15135.6 n/a Pi π Constant 3.1415927 n/a Antenna Efficiency η Gλ2/(π2D2) 0.63 n/a

Exhibit Radiation Hazard Report Page 2 of 10 1. Far Field Distance Calculation The distance to the beginning of the far field can be determined from the following equation: Distance to the Far Field Region Rff = 0.60 D2 / λ (1) = 71.1 m The maximum main beam power density in the far field can be determined from the following equation: On-Axis Power Density in the Far Field Sff = G P / (4 π Rff 2) (2) = 95.208 W/m2 = 9.521 mW/cm2 2. Near Field Calculation Power flux density is considered to be at a maximum value throughout the entire length of the defined Near Field region. The region is contained within a cylindrical volume having the same diameter as the antenna. Past the boundary of the Near Field region, the power density from the antenna decreases linearly with respect to increasing distance. The distance to the end of the Near Field can be determined from the following equation: Extent of the Near Field Rnf = D2 / (4 λ) (3) = 29.6 m The maximum power density in the Near Field can be determined from the following equation: Near Field Power Density Snf = 16.0 η P / (π D2) (4) = 222.256 W/m2 = 22.226 mW/cm2 3. Transition Region Calculation The Transition region is located between the Near and Far Field regions. The power density begins to decrease linearly with increasing distance in the Transition region. While the power density decreases inversely with distance in the Transition region, the power density decreases inversely with the square of the distance in the Far Field region. The maximum power density in the Transition region will not exceed that calculated for the Near Field region. The power density calculated in Section 1 is the highest power density the antenna can produce in any of the regions away from the antenna. The power density at a distance Rt can be determined from the following equation: Transition Region Power Density St = Snf Rnf / Rt (5) = 22.226 mW/cm2

Exhibit Radiation Hazard Report Page 3 of 10 Region between the Feed Assembly and the Antenna Reflector Transmissions from the feed assembly are directed toward the antenna reflector surface, and are confined within a conical shape defined by the type of feed assembly. The most common feed assemblies are waveguide flanges, horns or subreflectors. The energy between the feed assembly and reflector surface can be calculated by determining the power density at the feed assembly surface. This can be determined from the following equation: Power Density at the Feed Flange Sfa = 4000 P / Afa (6) = 35084.893 mW/cm2 4. Main Reflector Region The power density in the main reflector is determined in the same manner as the power density at the feed assembly. The area is now the area of the reflector aperture and can be determined from the following equation: Power Density at the Reflector Surface Ssurface = 4 P / Asurface (7) = 353.678 W/m2 = 35.368 mW/cm2 5. Region between the Reflector and the Ground Assuming uniform illumination of the reflector surface, the power density between the antenna and the ground can be determined from the following equation: Power Density between Reflector and Ground Sg = P / Asurface (8) = 88.419 W/m2 = 8.842 mW/cm2

Exhibit Radiation Hazard Report Page 4 of 10 6. Summary of Calculations Table 4. Summary of Expected Radiation levels for Uncontrolled Environment Calculated Maximum Radiation Power Density Level Region (mW/cm2) Hazard Assessment 1. Far Field (Rff = 71.1 m) Sff 9.521 Potential Hazard 2. Near Field (Rnf = 29.6 m) Snf 22.226 Potential Hazard 3. Transition Region (Rnf < Rt < Rff) St 22.226 Potential Hazard 4. Between Feed Assembly and Sfa 35084.893 Potential Hazard Antenna Reflector 5. Main Reflector Ssurface 35.368 Potential Hazard 6. Between Reflector and Ground Sg 8.842 Potential Hazard Table 5. Summary of Expected Radiation levels for Controlled Environment Calculated Maximum Radiation Power Density Region Level (mW/cm2) Hazard Assessment 1. Far Field (Rff = 71.1 m) Sff 9.521 Potential Hazard 2. Near Field (Rnf = 29.6 m) Snf 22.226 Potential Hazard 3. Transition Region (Rnf < Rt < Rff) St 22.226 Potential Hazard 4. Between Feed Assembly and Sfa 35084.893 Potential Hazard Antenna Reflector 5. Main Reflector Ssurface 35.368 Potential Hazard 6. Between Reflector and Ground Sg 8.842 Potential Hazard It is the applicant's responsibility to ensure that the public and operational personnel are not exposed to harmful levels of radiation. 7. Conclusions Based on the above analysis it is concluded that the FCC MPE guidelines have been exceeded (or met) in the regions of Table 4 and 5. The applicant proposes to comply with the MPE limits by one or more of the following methods. Radiation hazard signs will be posted while this earth station is in operation. The applicant proposes to comply with the MPE limits by one or more of the following methods. Radiation hazard signs will be posted while this earth station is in operation. The earth station is located on a Roof of a vehicle with secured access. All individuals having access to the roof will be aware of the Radiation Hazard from the antenna, thus creating a controlled environment. The earth station will be located approximately 12 feet above ground level and since one diameter removed from the center of main beam the levels are down at least 20 dB, or by a factor of 100, public safety will be ensured for the near and far field regions of the Uncontrolled Environment.

Exhibit Radiation Hazard Report Page 5 of 10 Means of Compliance Controlled Areas The earth station’s operational staff will not have access to the areas that exceed the MPE levels while the earth station is in operation. The transmitters will be turned off during antenna maintenance The applicant agrees to abide by the conditions specified in Condition 5208 provided below: Condition 5208 - The licensee shall take all necessary measures to ensure that the antenna does not create potential exposure of humans to radiofrequency radiation in excess of the FCC exposure limits defined in 47 CFR 1.1307(b) and 11.1310 wherever such exposures might occur. Measures must be taken to ensure compliance with limits for both occupational/controlled exposure and for general population/uncontrolled exposure, as defined in these rule sections. Compliance can be accomplished in most cases by appropriate restrictions such as fencing. Requirements for restrictions can be determined by predictions based on calculations, modeling or by field measurements. The FCC's OET Bulletin 65 (available on-line line at www.fcc.gov/oet/rfsafety) pprovides rovides information on predicting exposure levels and on methods for ensuring compliance, including the use of warning and alerting signs and protective equipment for worker. I HEREBY CERTIFY THAT I AM THE TECHNICALLY QUALIFIED PERSON RESPONSIBLE FOR THE PREPARATION OF THE RADIATION HAZARD REPORT, AND THAT IT IS COMPLETE AND CORRECT TO THE BEST OF MY KNOWLEDGE AND BELIEF. BY: _ Gary K. Edwards Senior Manager COMSEARCH 19700 Janelia Farm Boulevard Ashburn, VA 20147 DATED: November 24, 2014

Exhibit Radiation Hazard Report Page 6 of 10 Analysis of Non-Ionizing Radiation for a 2.4-Meter Ku-band Earth Station System This report analyzes the non-ionizing radiation levels for a 2.4-meter earth station system. The analysis and calculations performed in this report comply with the methods described in the FCC Office of Engineering and Technology Bulletin, No. 65 first published in 1985 and revised in 1997 in Edition 97-01. The radiation safety limits used in the analysis are in conformance with the FCC R&O 96-326. Bulletin No. 65 and the FCC R&O specifies that there are two separate tiers of exposure limits that are dependant on the situation in which the exposure takes place and/or the status of the individuals who are subject to the exposure. The Maximum Permissible Exposure (MPE) limits for persons in a General Population/Uncontrolled environment are shown in Table 1. The General Population/Uncontrolled MPE is a function of transmit frequency and is for an exposure period of thirty minutes or less. The MPE limits for persons in an Occupational/Controlled environment are shown in Table 2. The Occupational MPE is a function of transmit frequency and is for an exposure period of six minutes or less. The purpose of the analysis described in this report is to determine the power flux density levels of the earth station in the far-field, near-field, transition region, between the subreflector or feed and main reflector surface, at the main reflector surface, and between the antenna edge and the ground and to compare these levels to the specified MPEs. Table 1. Limits for General Population/Uncontrolled Exposure (MPE) Frequency Range (MHz) Power Density (mW/cm2) 30-300 0.2 300-1500 Frequency (MHz)*(0.8/1200) 1500-100,000 1.0 Table 2. Limits for Occupational/Controlled Exposure (MPE) Frequency Range (MHz) Power Density (mW/cm2) 30-300 1.0 300-1500 Frequency (MHz)*(4.0/1200) 1500-100,000 5.0 Table 3. Formulas and Parameters Used for Determining Power Flux Densities Parameter Symbol Formula Value Units Antenna Diameter D Input 2.4 m Antenna Surface Area Asurface π D2 / 4 4.52 m2 Feed Flange Diameter Dfa Input 7.6 cm Area of Feed Flange Afa π Dfa 2/4 45.60 cm2 Frequency F Input 14250 MHz Wavelength λ 300 / F 0.021053 m Transmit Power P Input 400.00 W Antenna Gain (dBi) Ges Input 49.3 dBi Antenna Gain (factor) G 10Ges/10 85113.8 n/a Pi π Constant 3.1415927 n/a Antenna Efficiency η Gλ2/(π2D2) 0.66 n/a

Exhibit Radiation Hazard Report Page 7 of 10 8. Far Field Distance Calculation The distance to the beginning of the far field can be determined from the following equation: Distance to the Far Field Region Rff = 0.60 D2 / λ (1) = 164.2 m The maximum main beam power density in the far field can be determined from the following equation: On-Axis Power Density in the Far Field Sff = G P / (4 π Rff 2) (2) = 100.535 W/m2 = 10.053 mW/cm2 9. Near Field Calculation Power flux density is considered to be at a maximum value throughout the entire length of the defined Near Field region. The region is contained within a cylindrical volume having the same diameter as the antenna. Past the boundary of the Near Field region, the power density from the antenna decreases linearly with respect to increasing distance. The distance to the end of the Near Field can be determined from the following equation: Extent of the Near Field Rnf = D2 / (4 λ) (3) = 68.4 m The maximum power density in the Near Field can be determined from the following equation: Near Field Power Density Snf = 16.0 η P / (π D2) (4) = 234.692 W/m2 = 23.469 mW/cm2 10. Transition Region Calculation The Transition region is located between the Near and Far Field regions. The power density begins to decrease linearly with increasing distance in the Transition region. While the power density decreases inversely with distance in the Transition region, the power density decreases inversely with the square of the distance in the Far Field region. The maximum power density in the Transition region will not exceed that calculated for the Near Field region. The power density calculated in Section 1 is the highest power density the antenna can produce in any of the regions away from the antenna. The power density at a distance Rt can be determined from the following equation: Transition Region Power Density St = Snf Rnf / Rt (5) = 23.469 mW/cm2

Exhibit Radiation Hazard Report Page 8 of 10 Region between the Feed Assembly and the Antenna Reflector Transmissions from the feed assembly are directed toward the antenna reflector surface, and are confined within a conical shape defined by the type of feed assembly. The most common feed assemblies are waveguide flanges, horns or subreflectors. The energy between the feed assembly and reflector surface can be calculated by determining the power density at the feed assembly surface. This can be determined from the following equation: Power Density at the Feed Flange Sfa = 4000 P / Afa (6) = 35084.893 mW/cm2 11. Main Reflector Region The power density in the main reflector is determined in the same manner as the power density at the feed assembly. The area is now the area of the reflector aperture and can be determined from the following equation: Power Density at the Reflector Surface Ssurface = 4 P / Asurface (7) = 353.678 W/m2 = 35.368 mW/cm2 12. Region between the Reflector and the Ground Assuming uniform illumination of the reflector surface, the power density between the antenna and the ground can be determined from the following equation: Power Density between Reflector and Ground Sg = P / Asurface (8) = 88.419 W/m2 = 8.842 mW/cm2

Exhibit Radiation Hazard Report Page 9 of 10 13. Summary of Calculations Table 4. Summary of Expected Radiation levels for Uncontrolled Environment Calculated Maximum Radiation Power Density Level Region (mW/cm2) Hazard Assessment 1. Far Field (Rff = 164.2 m) Sff 10.053 Potential Hazard 2. Near Field (Rnf = 68.4 m) Snf 23.469 Potential Hazard 3. Transition Region (Rnf < Rt < Rff) St 23.469 Potential Hazard 4. Between Feed Assembly and Sfa 35084.893 Potential Hazard Antenna Reflector 5. Main Reflector Ssurface 35.368 Potential Hazard 6. Between Reflector and Ground Sg 8.842 Potential Hazard Table 5. Summary of Expected Radiation levels for Controlled Environment Calculated Maximum Radiation Power Density Region Level (mW/cm2) Hazard Assessment 1. Far Field (Rff = 164.2 m) Sff 10.053 Potential Hazard 2. Near Field (Rnf = 68.4 m) Snf 23.469 Potential Hazard 3. Transition Region (Rnf < Rt < Rff) St 23.469 Potential Hazard 4. Between Feed Assembly and Sfa 35084.893 Potential Hazard Antenna Reflector 5. Main Reflector Ssurface 35.368 Potential Hazard 6. Between Reflector and Ground Sg 8.842 Potential Hazard It is the applicant's responsibility to ensure that the public and operational personnel are not exposed to harmful levels of radiation. 14. Conclusions Based on the above analysis it is concluded that the FCC MPE guidelines have been exceeded (or met) in the regions of Table 4 and 5. The applicant proposes to comply with the MPE limits by one or more of the following methods. Radiation hazard signs will be posted while this earth station is in operation. The applicant proposes to comply with the MPE limits by one or more of the following methods. Radiation hazard signs will be posted while this earth station is in operation. The earth station is located on a Roof of a vehicle with secured access. All individuals having access to the roof will be aware of the Radiation Hazard from the antenna, thus creating a controlled environment. The earth station will be located approximately 12 feet above ground level and since one diameter removed from the center of main beam the levels are down at least 20 dB, or by a factor of 100, public safety will be ensured for the near and far field regions of the Uncontrolled Environment.

Exhibit Radiation Hazard Report Page 10 of 10 Means of Compliance Controlled Areas The earth station’s operational staff will not have access to the areas that exceed the MPE levels while the earth station is in operation. The transmitters will be turned off during antenna maintenance The applicant agrees to abide by the conditions specified in Condition 5208 provided below: Condition 5208 - The licensee shall take all necessary measures to ensure that the antenna does not create potential exposure of humans to radiofrequency radiation in excess of the FCC exposure limits defined in 47 CFR 1.1307(b) and 11.1310 wherever such exposures might occur. Measures must be taken to ensure compliance with limits for both occupational/controlled exposure and for general population/uncontrolled exposure, as defined in these rule sections. Compliance can be accomplished in most cases by appropriate restrictions such as fencing. Requirements for restrictions can be determined by predictions based on calculations, modeling or by field measurements. The FCC's OET Bulletin 65 (available on-line line at www.fcc.gov/oet/rfsafety) pprovides rovides information on predicting exposure levels and on methods for ensuring compliance, including the use of warning and alerting signs and protective equipment for worker. I HEREBY CERTIFY THAT I AM THE TECHNICALLY QUALIFIED PERSON RESPONSIBLE FOR THE PREPARATION OF THE RADIATION HAZARD REPORT, AND THAT IT IS COMPLETE AND CORRECT TO THE BEST OF MY KNOWLEDGE AND BELIEF. BY: _ Gary K. Edwards Senior Manager COMSEARCH 19700 Janelia Farm Boulevard Ashburn, VA 20147 DATED: November 24, 2014


Document Created: 2014-11-21 15:43:33
Document Modified: 2014-11-21 15:43:33
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC